Jb-lighting Licon 1X Manuel d'utilisateur Page 110
- Page / 129
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
JB-lighting Lichtanlagen GmbH Sallersteigweg 15 D-89134 Blaustein Telefon ++49(0)7304 9617-0
- 110 -
Leave the PARAM menu by pressing the ESC key once. Then press the softkey RECORD to enter the
programming menu of the Timeline section. The following display will be shown:
The individual softkey have the following function:
M-CLR: deletes a marker
M-ADD: adds a marker
PLAY: plays the show from the start
PLAY: plays the show from a defined point in time
A-PLAY: plays the show within the programmed loop
FADE: enters the fade time
LOOP: activates the loop function
TRACK-/+: selects individual tracks
FRAME -/+: shifts the timeline forward or backward
ZOOM-/+: increases or reduces the time unit on the
display
M-CLR:
On the display in line „M“, up to 20 graphical markers can be set with the M-ADD key. These markers are
deleted simultaneously by pressing the softkey M-CLR.
M-ADD:
The softkey M-ADD is used to set graphical markers for orientation. A total of 20 markers are possible. To
set the markers, press the softkey M-ADD at the desired passages when the track is played.
PLAY:
The softkey PLAY starts and stops the timeline show.
Start: press the softkey PLAY once (displayed inverted on the display).
Stop: press the softkey PLAY again.
Important: If you start the show with the softkey PLAY, the track always starts from the beginning
(„00:00:00“).
-->PLAY:
This softkey starts the track from the passage, which is currently selected. It is also used to switch
forward from a loop.
A-Play:
The loop that you have set in the CD-Player menu will be played, when the softkey A-Play is pressed in
the Record menu. This softkey is also actived when a loop is programmed in the Record menu.
FADE:
With the softkey FADE, fade times are assigned to cues. If fade times have already been programmed for
a cues, you can change this fade time with the softkey FADE.
There are two possibilities to change the fade time:
Firstly:
If the softkey LOOP is activated while you are programming in the Record menu, you can read the current
fade time of the programmed cue directly off the display. You can change the fade time with the left
encoder wheel (FADE -/+).
Secondly:
Important: the softkey LOOP must not be activated here (display not inverted). Press and hold the softkey
FADE. Press and hold the cue key in addition. The fade time is determined by the time that you hold the
key pressed simultaneously.
LOOP:
The Loop function is activated, when the corresponding field is shown inverted on the display.
The Loop function is described in detail in Chapter 22.2 Entering basic parameters for timeline
programming (LOOP).
- User manual 1
- - 2 2
- Foreword 3
- General remarks 4
- Table of contents 5
- 1. First steps 10
- 2. Configuration (CONFIG) 11
- 2.5 P-COPY / Copying presets 17
- 2.10 The MIDI-function 21
- 3.2 Fixture groups 28
- 3.3 The Highlight/Group key 30
- 4. Presets 32
- 4.3 Recalling presets 33
- 4.4 Fading presets 33
- 5.1 Fan function 34
- 7. Editing cues 44
- + + + 45
- 7.4 Editing the name 46
- 7.8 Changing the fade time 47
- 7.9 Changing the trigpoint 47
- 9. Freeze function 49
- + 51
- 13.5 Changing direction 73
- 13.6 The Restart function 73
- 13.7 The Sync function 73
- 13.8 The Sound function 73
- 14.1 The LINK F function 75
- 14.2 The SINGLE function 75
- 14.3 The FLASH function 75
- 14.4 The NAME function 75
- 14.5 The MODIFY function 76
- 14.6 The TRACE function 76
- 14.7 The R-LINK function 76
- 14.8 The S-GROUP function 76
- 15. Sequences 77
- 15.2 The NAME function 79
- 15.3 The SINGLE function 79
- 15.4 The LINK F function 79
- 15.5 Entering runtimes 79
- 15.12 The BLOCK function 81
- 15.13 The LINK function 81
- 15.14 The RENUM function 81
- 16. Editing sequences 82
- 17. Working with sequences 84
- 17.3 The ENABLE key 85
- 18.1 Direct access 87
- 18.2 The ENCODE mode 88
- 18.3 The BLOCK mode 88
- 18.4 The HILITE mode 89
- 18.5 The PAROUT mode 89
- 19. The LIST function 96
- 20. Storing data (BACKUP) 98
- 20.3. The directory (DIR) 99
- 20.4 Loading data (LOAD) 99
- 20.5 Deleting a file 101
- 21. The Tool section 102
- 21.3 The CD-player (CD) 103
- 21.5 The INFO function 104
- 22.7 Playing a timeline show 114
- 23. Trackball 115
- 24.2 Updating the Licon 1X 117
- 25.1 Deleting all data 118
- 25.2 Deleting Config data 118
- 25.7 Deleting MIDI data 120
- 26.1 AUX CONTROLLERS 121
- 26.3 Display 121
- 26.4 FEATURE SELECTION 122
- 26.5 COMBI 122
- 26.6 PAR 122
- 26.7 CUES keypad 123
- 26.8 PAGE / BANK 123
- 26.9 CHASES 123
- 26.10 SEQUENCES 124
- 26.12 FADE-MODE 124
- 26.13 PAR faders 125
- 26.14 FIXTURE faders 125
- 26.15 CHASE-CONTROL 126
- 26.16 SEQUENCE-CONTROL 126
- - 127 127
- 28. LICON 1X for hire 128
- 29. LICON 1X Customer List 129
Produits connexes et manuels pour Éclairage Jb-lighting Licon 1X
(31 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.544 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels