Jb-lighting Licon 1X Manuel d'utilisateur Page 16
- Page / 129
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
JB-lighting Lichtanlagen GmbH Sallersteigweg 15 D-89134 Blaustein Telefon ++49(0)7304 9617-0
- 16 -
2.4 PATCH / Assigning DMX channels to the dimmer/PAR section
In analogy to the fixture section, the Patch menu is also used to assign DMX channels are assigned to
the dimmer/PAR section. Enter CONFIG menu and select the menu item PATCH. Press the PAR1 key
and the following display is shown:
The softkeys listed below have the following functions:
SCAN 1: enters DMX addresses for fixture no. 1 – 16
SCAN 2: enters DMX addresses for fiixture no. 17-32
AUX: enters DMX addresses for AUX controllers
PAR1: enters DMX addresses for dimmer channel 1-16
PAR2: enters DMX addresses for dimmer channel 17-32
PAR3: enters DMX addresses for dimmer channel 33-48
PAR4: enters DMX addresses for dimmer channel 49-64
PAR5: enters DMX addresses for dimmer channel 64-80
PAR6: enters DMX addresses for dimmer channel 81-96
A/B: selects the DMX output
CURVE: selects the dimmer curve
CLEAR: deletes all DMX addresses
OPEN: deletes an individual DMX address
PATCH: confirms data input
Left encoder wheel: selects DMX addresses
Middle encoder wheel: moves the cursor up and down
Right encoder wheel: moves the cursor to the left and right
2.4.1 Entering DMX start addresses for the dimmer/PAR section
You can assign up to four DMX addresses to each Par key (1-32). Enter Patch menu and select PAR 1.
Use the middle or right encoder wheel to select the key in the Fixture-/PAR Selection, for which you wish
to enter DMX start addresses. Use the left encoder wheel to select DMX addresses.
Since the Licon 1X comes with two separate DMX outputs, select the DMX lines A or B by pressing the
softkey A/B.
Press the softkey PATCH to confirm the assignment of the channel.
After each confirmation with the softkey PATCH, the cursor jumps to the next position and the next not
occupied DMX channel is recommended automatically by the controller. You will only have to confirm with
PATCH.
2.4.2 Deleting particular DMX start addresses
To delete the DMX assignment of one particular key, select this key with the middle encoder wheel and
press the softkey OPEN.
2.4.3 Deleting all DMX start addresses
If you wish to delete all start addresses, enter
CONFIG/PATCH menu and press the softkey CLEAR. The
menu shown on the left appears on the display:
After you have pressed one of the the softkeys ALL, SCAN,
AUX or PAR, the deletion procedure starts immediately
without prior confirmation prompt. Press the ESC key if you do not wish to delete a start address.
ALL: deletes all DMX start addresses
SCAN: deletes start addresses of fixtues
AUX: deletes start addresses of AUX controllers
PAR: deletes DMX assignment of dimmer/PAR channels
Press the ESC key to leave this menu.
- User manual 1
- - 2 2
- Foreword 3
- General remarks 4
- Table of contents 5
- 1. First steps 10
- 2. Configuration (CONFIG) 11
- 2.5 P-COPY / Copying presets 17
- 2.10 The MIDI-function 21
- 3.2 Fixture groups 28
- 3.3 The Highlight/Group key 30
- 4. Presets 32
- 4.3 Recalling presets 33
- 4.4 Fading presets 33
- 5.1 Fan function 34
- 7. Editing cues 44
- + + + 45
- 7.4 Editing the name 46
- 7.8 Changing the fade time 47
- 7.9 Changing the trigpoint 47
- 9. Freeze function 49
- + 51
- 13.5 Changing direction 73
- 13.6 The Restart function 73
- 13.7 The Sync function 73
- 13.8 The Sound function 73
- 14.1 The LINK F function 75
- 14.2 The SINGLE function 75
- 14.3 The FLASH function 75
- 14.4 The NAME function 75
- 14.5 The MODIFY function 76
- 14.6 The TRACE function 76
- 14.7 The R-LINK function 76
- 14.8 The S-GROUP function 76
- 15. Sequences 77
- 15.2 The NAME function 79
- 15.3 The SINGLE function 79
- 15.4 The LINK F function 79
- 15.5 Entering runtimes 79
- 15.12 The BLOCK function 81
- 15.13 The LINK function 81
- 15.14 The RENUM function 81
- 16. Editing sequences 82
- 17. Working with sequences 84
- 17.3 The ENABLE key 85
- 18.1 Direct access 87
- 18.2 The ENCODE mode 88
- 18.3 The BLOCK mode 88
- 18.4 The HILITE mode 89
- 18.5 The PAROUT mode 89
- 19. The LIST function 96
- 20. Storing data (BACKUP) 98
- 20.3. The directory (DIR) 99
- 20.4 Loading data (LOAD) 99
- 20.5 Deleting a file 101
- 21. The Tool section 102
- 21.3 The CD-player (CD) 103
- 21.5 The INFO function 104
- 22.7 Playing a timeline show 114
- 23. Trackball 115
- 24.2 Updating the Licon 1X 117
- 25.1 Deleting all data 118
- 25.2 Deleting Config data 118
- 25.7 Deleting MIDI data 120
- 26.1 AUX CONTROLLERS 121
- 26.3 Display 121
- 26.4 FEATURE SELECTION 122
- 26.5 COMBI 122
- 26.6 PAR 122
- 26.7 CUES keypad 123
- 26.8 PAGE / BANK 123
- 26.9 CHASES 123
- 26.10 SEQUENCES 124
- 26.12 FADE-MODE 124
- 26.13 PAR faders 125
- 26.14 FIXTURE faders 125
- 26.15 CHASE-CONTROL 126
- 26.16 SEQUENCE-CONTROL 126
- - 127 127
- 28. LICON 1X for hire 128
- 29. LICON 1X Customer List 129
Produits connexes et manuels pour Éclairage Jb-lighting Licon 1X
(31 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.395 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels