Jb-lighting Licon 1X Manuel d'utilisateur Page 54
- Page / 129
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
JB-lighting Lichtanlagen GmbH Sallersteigweg 15 D-89134 Blaustein Telefon ++49(0)7304 9617-0
- 54 -
The runtimes of the chases can be changed manually in the Chase Control section ( see chapter 13)
Duration of the individual steps (speed)
The duration of a step is entered with the encoder wheel (speed) in the Chase Control
section.
It is also possible, to change the duration later (also in the Chase Control section).
Duration of the fade time / specified in percent
The fade time accesses all parameters that are marked with a fade ramp in the storage matrix (cf.:
Chapter 6.1.1 The storage matrix).
If the fade time is entered as percentage value, this in relation to the duration of the step
(speed). If a chase step lasts 5 seconds and the fade time is entered with 50%, then all
parameters capable of fading are faded in within 2.5 seconds.
If you wish to enter the fade time in percent, make sure that the softkey LINK-F is displayed
inverted. Enter the values with the left encoder wheel.
Duration of the fade time / specified in seconds
You can enter the fade time independent of the duration of the chase steps themselves. Press the softkey
LINK-F. When the field is no longer displayed inverted, you can enter the fade time with the left encoder
wheel. The values are entered in steps of 0.0250 seconds.
Keep in mind that the fade time will not be readjusted automatically, when the duration of the chase is
changed manually. Possible changes must be entered manually for each chase step. It is also important
that the fade time is not longer than the
chase step itself, since otherwise the step
cannot be imaged completely.
Trigpoint
Trigpoint designates the moment, at which
all parameters are switched that are not
faded. These channels are not marked with
a fade ramp in the storage matrix (cf.: 6.1.1
The storage matrix).
The trigpoint is specified in percent of the
total duration of the step. If the duration of a
chase step is 5 seconds and the trigpoint is
set at 75%, parameters such as gobo and prism are switched to the new DMX value after 3.75 seconds.
11.1.5 Inserting a chase step
If not otherwise specified, each new step is added to the existing chase during the storage process.
If you wish to insert the chase step to another position within the chase, use the middle encoder wheel
(STEP) to scroll up and down the existing steps. As soon as the encoder wheel is moved, the softkey
INSERT is shown on the display.
- User manual 1
- - 2 2
- Foreword 3
- General remarks 4
- Table of contents 5
- 1. First steps 10
- 2. Configuration (CONFIG) 11
- 2.5 P-COPY / Copying presets 17
- 2.10 The MIDI-function 21
- 3.2 Fixture groups 28
- 3.3 The Highlight/Group key 30
- 4. Presets 32
- 4.3 Recalling presets 33
- 4.4 Fading presets 33
- 5.1 Fan function 34
- 7. Editing cues 44
- + + + 45
- 7.4 Editing the name 46
- 7.8 Changing the fade time 47
- 7.9 Changing the trigpoint 47
- 9. Freeze function 49
- + 51
- 13.5 Changing direction 73
- 13.6 The Restart function 73
- 13.7 The Sync function 73
- 13.8 The Sound function 73
- 14.1 The LINK F function 75
- 14.2 The SINGLE function 75
- 14.3 The FLASH function 75
- 14.4 The NAME function 75
- 14.5 The MODIFY function 76
- 14.6 The TRACE function 76
- 14.7 The R-LINK function 76
- 14.8 The S-GROUP function 76
- 15. Sequences 77
- 15.2 The NAME function 79
- 15.3 The SINGLE function 79
- 15.4 The LINK F function 79
- 15.5 Entering runtimes 79
- 15.12 The BLOCK function 81
- 15.13 The LINK function 81
- 15.14 The RENUM function 81
- 16. Editing sequences 82
- 17. Working with sequences 84
- 17.3 The ENABLE key 85
- 18.1 Direct access 87
- 18.2 The ENCODE mode 88
- 18.3 The BLOCK mode 88
- 18.4 The HILITE mode 89
- 18.5 The PAROUT mode 89
- 19. The LIST function 96
- 20. Storing data (BACKUP) 98
- 20.3. The directory (DIR) 99
- 20.4 Loading data (LOAD) 99
- 20.5 Deleting a file 101
- 21. The Tool section 102
- 21.3 The CD-player (CD) 103
- 21.5 The INFO function 104
- 22.7 Playing a timeline show 114
- 23. Trackball 115
- 24.2 Updating the Licon 1X 117
- 25.1 Deleting all data 118
- 25.2 Deleting Config data 118
- 25.7 Deleting MIDI data 120
- 26.1 AUX CONTROLLERS 121
- 26.3 Display 121
- 26.4 FEATURE SELECTION 122
- 26.5 COMBI 122
- 26.6 PAR 122
- 26.7 CUES keypad 123
- 26.8 PAGE / BANK 123
- 26.9 CHASES 123
- 26.10 SEQUENCES 124
- 26.12 FADE-MODE 124
- 26.13 PAR faders 125
- 26.14 FIXTURE faders 125
- 26.15 CHASE-CONTROL 126
- 26.16 SEQUENCE-CONTROL 126
- - 127 127
- 28. LICON 1X for hire 128
- 29. LICON 1X Customer List 129
Produits connexes et manuels pour Éclairage Jb-lighting Licon 1X
(31 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.750 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels