Jb-lighting Licon 1X Manuel d'utilisateur Page 15
- Page / 129
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
JB-lighting Lichtanlagen GmbH Sallersteigweg 15 D-89134 Blaustein Telefon ++49(0)7304 9617-0
- 15 -
The individual softkeys have the following function:
SCAN 1: enters DMX addresses for fixture no. 1 – 16
SCAN 2: enters DMX addresses for fiixture no. 17-32
AUX: enters DMX addresses for AUX controllers
PAR1: enters DMX addresses for dimmer channel 1-16
PAR2: enters DMX addresses for dimmer channel 17-32
PAR3: enters DMX addresses for dimmer channel 33-48
PAR4: enters DMX addresses for dimmer channel 49-64
PAR5: enters DMX addresses for dimmer channel 64-80
PAR6: enters DMX addresses for dimmer channel 81-96
A/B: selects the DMX output
CLEAR: deletes all DMX addresses
OPEN: deletes an individual DMX address
PATCH: confirms data input
Left encoder wheel: selects DMX addresses
Middle encoder wheel: moves the cursor up and down
Right encoder wheel: moves the cursor to the left and right
2.3.1 Entering DMX start addresses for fixtures
Press the softkey PATCH. The first fixture in the fixture list is automatically activated and start address
no. 1 or the first not occupied DMX address is recommended by the controller for the patch (DMX
channels cannot be double-assigned). If you wish to control fixture no. 1 with DMX channel 1, DMX line
A, then confirm by pressing the softkey PATCH. Now the second fixture of the list is displayed inverted
and the controller automatically recommends the next not occupied channel for the patch. (The example
above recommends DMX channel 9, since the Varyscan 4 is controlled with 8 DMX channels.) Press the
softkey PATCH again to confirm this start address. If you need a start address other than that
recommended by the controller, select the desired start address with the left encoder wheel and press the
softkey PATCH for confirmation.
Select the fixtures with the middle encoder wheel.
Press the softkey A/B to determine the DMX line of the fixtures.
Press the ESC key to leave this menu.
2.3.2 Deleting a particular start address
To delete a particular start address, press the softkey CONFIG/PATCH to enter the Patch menu. Select
the corresponding fixture with the centre encoder wheel. As soon as the fixture is displayed inverted,
press the softkey OPEN to delete the start address.
Press the ESC key to leave this menu.
2.3.3 Deleting all start addresses
If you wish to delete all start addresses, enter CONFIG/PATCH menu and press the softkey CLEAR. The
following selection appears on the display:
ALL: deletes all DMX start addresses
SCAN: deletes start addresses of moving lights
AUX: deletes start addresses of AUX controllers
PAR: deletes DMX assignment of dimmer/PAR channels
After you have pressed one of the the softkeys ALL, SCAN, AUX or PAR, the corresponding parameters
are deleted without prior confirmation prompt. Press the ESC key if you do not wish to delete a start
address.
Press the ESC key to leave this menu.
- User manual 1
- - 2 2
- Foreword 3
- General remarks 4
- Table of contents 5
- 1. First steps 10
- 2. Configuration (CONFIG) 11
- 2.5 P-COPY / Copying presets 17
- 2.10 The MIDI-function 21
- 3.2 Fixture groups 28
- 3.3 The Highlight/Group key 30
- 4. Presets 32
- 4.3 Recalling presets 33
- 4.4 Fading presets 33
- 5.1 Fan function 34
- 7. Editing cues 44
- + + + 45
- 7.4 Editing the name 46
- 7.8 Changing the fade time 47
- 7.9 Changing the trigpoint 47
- 9. Freeze function 49
- + 51
- 13.5 Changing direction 73
- 13.6 The Restart function 73
- 13.7 The Sync function 73
- 13.8 The Sound function 73
- 14.1 The LINK F function 75
- 14.2 The SINGLE function 75
- 14.3 The FLASH function 75
- 14.4 The NAME function 75
- 14.5 The MODIFY function 76
- 14.6 The TRACE function 76
- 14.7 The R-LINK function 76
- 14.8 The S-GROUP function 76
- 15. Sequences 77
- 15.2 The NAME function 79
- 15.3 The SINGLE function 79
- 15.4 The LINK F function 79
- 15.5 Entering runtimes 79
- 15.12 The BLOCK function 81
- 15.13 The LINK function 81
- 15.14 The RENUM function 81
- 16. Editing sequences 82
- 17. Working with sequences 84
- 17.3 The ENABLE key 85
- 18.1 Direct access 87
- 18.2 The ENCODE mode 88
- 18.3 The BLOCK mode 88
- 18.4 The HILITE mode 89
- 18.5 The PAROUT mode 89
- 19. The LIST function 96
- 20. Storing data (BACKUP) 98
- 20.3. The directory (DIR) 99
- 20.4 Loading data (LOAD) 99
- 20.5 Deleting a file 101
- 21. The Tool section 102
- 21.3 The CD-player (CD) 103
- 21.5 The INFO function 104
- 22.7 Playing a timeline show 114
- 23. Trackball 115
- 24.2 Updating the Licon 1X 117
- 25.1 Deleting all data 118
- 25.2 Deleting Config data 118
- 25.7 Deleting MIDI data 120
- 26.1 AUX CONTROLLERS 121
- 26.3 Display 121
- 26.4 FEATURE SELECTION 122
- 26.5 COMBI 122
- 26.6 PAR 122
- 26.7 CUES keypad 123
- 26.8 PAGE / BANK 123
- 26.9 CHASES 123
- 26.10 SEQUENCES 124
- 26.12 FADE-MODE 124
- 26.13 PAR faders 125
- 26.14 FIXTURE faders 125
- 26.15 CHASE-CONTROL 126
- 26.16 SEQUENCE-CONTROL 126
- - 127 127
- 28. LICON 1X for hire 128
- 29. LICON 1X Customer List 129
Produits connexes et manuels pour Éclairage Jb-lighting Licon 1X
(31 pages)
© 2020, manymanuals.fr. Tous droits réservés | 4.393 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels